Replacing a Larson storm door handle may seem like a daunting task, but with the right tools and a little know-how, you can easily do it yourself. Before you begin, gather the necessary tools including a Phillips head screwdriver, a flathead screwdriver, and a new handle. Additionally, you will need a tape measure or ruler to ensure that the new handle is the correct size. With these items in hand, you can follow these simple steps to replace your Larson storm door handle.
First, remove the old handle. To do this, locate the two screws that are holding the handle in place and remove them using a Phillips head screwdriver. Once the screws are removed, gently pull the handle straight towards you to detach it from the door. Next, measure the distance between the two mounting holes on the door. This measurement will determine the size of the new handle that you need to purchase. Once you have the new handle, align it with the mounting holes on the door and insert the screws.
Finally, tighten the screws until the handle is securely attached to the door. Be careful not to overtighten the screws, as this could damage the door or the handle. Once the handle is tight, test it by opening and closing the door to ensure that it is functioning properly. If the handle is loose or does not open and close smoothly, adjust the screws accordingly. With these simple steps, you can easily replace a Larson storm door handle and keep your door functioning properly.
Safety Considerations
Before attempting to replace the door handle on your Larson door, it is crucial to prioritize your safety by adhering to the following guidelines:
1. Disconnect Electrical Power:
- Locate the circuit breaker or fuse box for your home and identify the breaker or fuse that controls the electrical system to the door.
- Switch off the breaker or remove the fuse to cut off the power supply to the door.
- Double-check that the power is disconnected by testing the door’s operation. If it does not work, it is safe to proceed.
2. Wear Protective Gear:
- Wear safety glasses to protect your eyes from flying debris or sharp edges.
- Wear work gloves to prevent cuts or abrasions from handling door components.
3. Observe Proper Body Mechanics:
- Avoid bending over or reaching awkwardly to prevent muscle strains or sprains.
- Use a step stool or ladder for stability when working on the door from a height.
- Take breaks as needed to avoid fatigue and potential injuries.
Additional Tips:
| Tip |
|---|
| Have a helper assist you to hold the door in place or pass you tools. |
| Lay down a drop cloth or blanket to prevent scratches or damage to the door or floor. |
| Take your time and carefully follow the instructions to ensure a secure and functional replacement. |
How to Replace a Larson Door Handle
Replacing a Larson door handle is a relatively simple task that can be completed in a few minutes with the right tools. Here are the steps on how to do it:
Gather the necessary tools, including a Phillips head screwdriver and a new Larson door handle.
Remove the two screws that are holding the old door handle in place. The screws are located on the inside of the door, near the handle.
Pull the old door handle straight out of the door. Be careful not to damage the door frame.
Insert the new door handle into the door. Make sure that the handle is facing the correct way.
Secure the new door handle with the two screws. Tighten the screws until they are snug.
Test the new door handle to make sure that it is working properly.
People Also Ask
How do you remove a Larson storm door handle?
To remove a Larson storm door handle, follow these steps:
Locate the two screws that are holding the handle in place. The screws are usually located on the inside of the door, near the handle.
Remove the two screws using a Phillips head screwdriver.
Pull the handle straight out of the door. Be careful not to damage the door frame.
How do you install a Larson storm door handle?
To install a Larson storm door handle, follow these steps:
Insert the handle into the door. Make sure that the handle is facing the correct way.
Secure the handle with the two screws. Tighten the screws until they are snug.
Test the new handle to make sure that it is working properly.